? semiconductor components industries, llc, 2014 march, 2014 ? rev. 10 1 publication order number: nl27wz125/d nl27wz125 dual buffer with 3-state outputs the nl27wz125 is a high performance dual noninverting buffer operating from a 1.65 v to 5.5 v supply. features ? extremely high speed: t pd 2.6 ns (typical) at v cc = 5 v ? designed for 1.65 v to 5.5 v v cc operation ? over voltage tolerant inputs and outputs ? lvttl compatible ? interface capability with 5 v ttl logic with v cc = 3 v ? lvcmos compatible ? 24 ma balanced output sink and source capability ? near zero static supply current substantially reduces system power requirements ? 3 ? state oe input is active ? low ? replacement for nc7wz125 ? chip complexity = 72 fets ? nlv prefix for automotive and other applications requiring unique site and control change requirements; aec ? q100 qualified and ppap capable ? these devices are pb ? free and are rohs compliant a 2 y 2 en figure 1. pinout (top view) figure 2. logic symbol 1 y 1 a 1 oe 2 oe 1 v cc oe 1 a 1 gnd 1 2 3 8 7 6 45 y 2 oe 2 y 1 a 2 http://onsemi.com marking diagram see detailed ordering and shipping information in the package dimensions section on page 2 of this data sheet. ordering information pin assignment pin 1 2 3 4 5 6 7 8 function oe 1 a 1 y 2 gnd a 2 y 1 oe 2 v cc input function table a n l h x output y n l h z oe n l l h x = don?t care n = 1, 2 us8 us suffix case 493 1 8 m0 = device code m = date code* = pb ? free package m0 m *date code orientation may vary depending upon manufacturing location. (note: microdot may be in either location)
nl27wz125 http://onsemi.com 2 maximum ratings symbol parameter value units v cc dc supply voltage ? 0.5 to +7.0 v v i dc input voltage ? 0.5 to +7.0 v v o dc output voltage output in high impedance state output in high or low state ? 0.5 to +7.0 ? 0.5 to v cc + 0.5 v i ik dc input diode current, v i < gnd ? 50 ma i ok dc output diode current, v o < gnd ? 50 ma i o dc output sink current 50 ma i cc dc supply current per supply pin 100 ma i gnd dc ground current per ground pin 100 ma t stg storage temperature range ? 65 to +150 c t l lead temperature, 1 mm from case for 10 seconds 260 c t j junction temperature under bias +150 c ja thermal resistance (note 1) 250 c/w p d power dissipation in still air at 85 c 250 mw msl moisture sensitivity level 1 f r flammability rating ? oxygen index: 28 to 34 ul 94 v ? 0 @ 0.125 in v esd esd withstand voltage human body model (note 2) machine model (note 3) charged device model (note 4) > 2000 > 200 n/a v i latchup latchup performance above v cc and below gnd at 125 c (note 5) 100 ma stresses exceeding those listed in the maximum ratings table may damage the device. if any of these limits are exceeded, device function ality should not be assumed, damage may occur and reliability may be affected. 1. measured with minimum pad spacing on an fr4 board, using 10 mm ? by ? 1 inch, 2 ? ounce copper trace with no air flow. 2. tested to eia/jesd22 ? a114 ? a. 3. tested to eia/jesd22 ? a115 ? a. 4. tested to jesd22 ? c101 ? a. 5. tested to eia/jesd78. recommended operating conditions symbol parameter min max units v cc supply voltage operating data retention only 1.65 1.5 5.5 5.5 v v i input voltage (note 6) 0 5.5 v v o output voltage (high or low state) 0 5.5 v t a operating free ? air temperature ? 55 +125 c t/ v input transition rise or fall rate v cc = 2.5 v 0.2 v v cc = 3.0 v 0.3 v v cc = 5.0 v 0.5 v 0 0 0 20 10 5 ns/v functional operation above the stresses listed in the recommended operating ranges is not implied. extended exposure to stresse s beyond the recommended operating ranges limits may affect device reliability. 6. unused inputs may not be left open. all inputs must be tied to a high ? or low ? logic input voltage level. device ordering information device order number package type shipping ? nl27wz125usg us8 (pb ? free) 3000 / tape & reel NLV27WZ125USG* ?for information on tape and reel specifications, including part orientation and tape sizes, please refer to our tape and reel packaging specifications brochure, brd8011/d. *nlv prefix for automotive and other applications requiring unique site and control change requirements; aec ? q100 qualified and ppap capable.
nl27wz125 http://onsemi.com 3 dc electrical characteristics symbol parameter condition v cc (v) t a = 25 c ? 55 c t a 125 c units min typ max min max v ih high ? level input voltage 1.65 2.3 to 5.5 0.75 v cc 0.7 v cc 0.75 v cc 0.7 v cc v v il low ? level input voltage 1.65 2.3 to 5.5 0.25 v cc 0.3 v cc 0.25 v cc 0.3 v cc v v oh high ? level output voltage v in = v il or v ih i oh = 100 a i oh = ? 3 ma i oh = ? 8 ma i oh = ? 12 ma i oh = ? 16 ma i oh = ? 24 ma i oh = ? 32 ma 1.65 to 5.5 1.65 2.3 2.7 3.0 3.0 4.5 v cc ? 0.1 1.29 1.9 2.2 2.4 2.3 3.8 v cc 1.52 2.1 2.4 2.7 2.5 4.0 v cc ? 0.1 1.29 1.9 2.2 2.4 2.3 3.8 v v ol low ? level output voltage v in = v il i ol = 100 a i ol = 3 ma i ol = 8 ma i ol = 12 ma i ol = 16 ma i ol = 24 ma i ol = 32 ma 1.65 to 5.5 2.3 2.7 3.0 3.0 4.5 0.08 0.20 0.22 0.28 0.38 0.42 0.1 0.24 0.3 0.4 0.4 0.55 0.55 0.1 0.24 0.3 0.4 0.4 0.55 0.55 v i in input leakage current v in = 5.5v or gnd 0 to 5.5 0.1 1.0 a i off power off leakage current v in = 5.5 v or v out = 5.5 v 0 1.0 10 a i cc quiescent supply current v in = 5.5v or gnd 5.5 1.0 10 a i oz 3 ? state output leakage v in = v il or v ih 0v v out 5.5 v 2.3 to 5.5 0.5 5 a product parametric performance is indicated in the electrical characteristics for the listed test conditions, unless otherwise noted. product performance may not be indicated by the electrical characteristics if operated under different conditions. ac electrical characteristics (t r = t f = 3.0 ns) symbol parameter condition v cc (v) t a = 25 c ? 55 c t a 125 c units min typ max min max t plh t phl propagation delay an to yn (figures 3 and 4) r l = 1 m , c l = 15 pf 1.8 0.15 2.5 0.2 2.0 1.0 12 7.5 2.0 1.0 13 8 ns r l = 1 m , c l = 15 pf r l = 500 , c l = 50 pf 3.3 0.3 0.8 1.2 5.2 5.7 0.8 1.2 5.5 6.0 r l = 1 m , c l = 15 pf r l = 500 , c l = 50 pf 5.0 0.5 0.5 0.8 4.5 5.0 0.5 0.8 4.8 5.3 t oslh t oshl output to output skew (note 7) r l = 500 , c l = 50 pf 3.3 0.3 1.0 1.0 ns r l = 500 , c l = 50 pf 5.0 0.5 0.8 0.8 t pzh t pzl output enable time (figures 5, 6 and 7) 1.8 0.15 2.5 0.2 3.0 1.8 14 8.5 3.0 1.8 15 9.0 ns 3.3 0.3 1.2 6.2 1.2 6.5 5.0 0.5 0.8 5.5 0.8 5.8 t phz t plz output enable time (figures 5, 6 and 7) 1.8 0.15 2.5 0.2 2.5 1.5 12 8.0 2.5 1.5 13 8.5 ns 3.3 0.3 0.8 5.7 0.8 6.0 5.0 0.5 0.3 4.7 0.3 5.0 7. skew is defined as the absolute value of the dif ference between the actual propagation delay for any two separate outputs of the same d evice. this specification applies to any outputs switching in the same direction, either high ? to ? low (t oshl ) or low ? to ? high (t oslh ); parameter guaranteed by design.
nl27wz125 http://onsemi.com 4 capacitive characteristics symbol parameter condition typical units c in input capacitance v cc = 5.5 v, v i = 0 v or v cc 7.0 pf c out output capacitance v cc = 5.5 v, v i = 0 v or v cc 7.0 pf c pd power dissipation capacitance (note 8) 10 mhz, v cc = 3.3 v, v i = 0 v or v cc 10 mhz, v cc = 5.5 v, v i = 0 v or v cc 18 27 pf 8. c pd is defined as the value of the internal equivalent capacitance which is calculated from the operating current consumption with out load. average operating current can be obtained by the equation: i cc(opr ) = c pd v cc f in + i cc . c pd is used to determine the no ? load dynamic power consumption; p d = c pd v cc 2 f in + i cc v cc . c l * figure 3. switching waveform input r l *includes all probe and jig capacitance. a 1 mhz square input wave is recommended for propagation delay tests. figure 4. t plh or t phl t f = 3 ns v cc gnd v oh v ol 90% 50% 10% t plh t phl output y input a and b t f = 3 ns 90% 50% 10% output oe = gnd 50% 50% v cc 0 v 0 v oe on t pzh v cc t phz t pzl t plz on 50% 50% 50% v cc v oh ? 10% v ol + 10% gnd 50% figure 5. ac output enable and disable waveform figure 6. t pzl or t pl a 1 mhz square input wave is recommended for propagation delay tests. figure 7. t pzh or t phz a 1 mhz square input wave is recommended for propagation delay tests. c l = 50 pf r l = 500 output input r 1 = 500 2 v cc c l = 50 pf r l = 250 output v cc input
nl27wz125 http://onsemi.com 5 package dimensions us8 case 493 ? 02 issue b dim a min max min max inches 1.90 2.10 0.075 0.083 millimeters b 2.20 2.40 0.087 0.094 c 0.60 0.90 0.024 0.035 d 0.17 0.25 0.007 0.010 f 0.20 0.35 0.008 0.014 g 0.50 bsc 0.020 bsc h 0.40 ref 0.016 ref j 0.10 0.18 0.004 0.007 k 0.00 0.10 0.000 0.004 l 3.00 3.20 0.118 0.126 m 0 6 0 6 n 5 10 5 10 p 0.23 0.34 0.010 0.013 r 0.23 0.33 0.009 0.013 s 0.37 0.47 0.015 0.019 u 0.60 0.80 0.024 0.031 v 0.12 bsc 0.005 bsc notes: 1. dimensioning and tolerancing per ansi y14.5m, 1982. 2. controlling dimension: millimeters. 3. dimension ?a? does not include mold flash, protrusion or gate burr. mold flash. protrusion and gate burr shall not exceed 0.140 mm (0.0055?) per side. 4. dimension ?b? does not include inter ? lead flash or protrusion. inter ? lead flash and protrusion shall not e3xceed 0.140 (0.0055?) per side. 5. lead finish is solder plating with thickness of 0.0076 ? 0.0203 mm. (300 ? 800 ?). 6. all tolerance unless otherwise specified 0.0508 (0.0002 ?). l b a p g 4 1 5 8 c k d seating j s r u detail e v f h n r 0.10 typ m ? y ? ? x ? ? t ? detail e t m 0.10 (0.004) xy t 0.10 (0.004) plane *for additional information on our pb ? free strategy and soldering details, please download the on semiconductor soldering and mounting techniques reference manual, solderrm/d. soldering footprint* mm inches scale 8:1 3.8 0.15 0.50 0.0197 1.0 0.0394 0.30 0.012 1.8 0.07 on semiconductor and are registered trademarks of semiconductor co mponents industries, llc (scillc). scillc owns the rights to a numb er of patents, trademarks, copyrights, trade secrets, and other inte llectual property. a listing of scillc?s product/patent coverage may be accessed at ww w.onsemi.com/site/pdf/patent ? marking.pdf. scillc reserves the right to make changes without further notice to any products herein. scillc makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does scillc assume any liability arising out of the application or use of any product or circuit, and s pecifically disclaims any and all liability, including without limitation special, consequential or incidental damages. ?typical? parameters which may be provided in scillc data sheets and/ or specifications can and do vary in different applications and actual performance may vary over time. all operating parameters, including ?typical s? must be validated for each customer application by customer?s technical experts. scillc does not convey any license under its patent rights nor the right s of others. scillc products are not designed, intended, or a uthorized for use as components in systems intended for surgical implant into the body, or other applications intended to support or sustain life, or for any other application in whic h the failure of the scillc product could create a situation where personal injury or death may occur. should buyer purchase or us e scillc products for any such unintended or unauthorized appli cation, buyer shall indemnify and hold scillc and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unin tended or unauthorized use, even if such claim alleges that scil lc was negligent regarding the design or manufacture of the part. scillc is an equal opportunity/affirmative action employer. this literature is subject to all applicable copyrig ht laws and is not for resale in any manner. publication ordering information n. american technical support : 800 ? 282 ? 9855 toll free usa/canada europe, middle east and africa technical support: phone: 421 33 790 2910 japan customer focus center phone: 81 ? 3 ? 5817 ? 1050 nl27wz125/d literature fulfillment : literature distribution center for on semiconductor p.o. box 5163, denver, colorado 80217 usa phone : 303 ? 675 ? 2175 or 800 ? 344 ? 3860 toll free usa/canada fax : 303 ? 675 ? 2176 or 800 ? 344 ? 3867 toll free usa/canada email : orderlit@onsemi.com on semiconductor website : www.onsemi.com order literature : http://www.onsemi.com/orderlit for additional information, please contact your local sales representative
|
